![]() ![]()
The lags i experience in this game are pretty tolerable even if they may occur occasionally. It runs flawlessly with running speeds of around 40-54 fps and seldom lags & crashes are rare making this game playable from start to finish. I will look at fairchild too.*Available in HD* My attempt to run the PS2 game SSX On Tour on the PCSX2 0.9.8 r4600 emulator. ![]() The originals mentioned in the schematic cost too much but these come very close or are even similar to the originals.anyway they are more powerful than the IRFP460. I did a search in my local stores provided device list and the best I could come up with was either IXTH24N50L or IXFH24N50. #SG3525 IR2110 SMPS RAREST FULL#The SG3525 that drives the IR2110 in my circuit has a soft start circuit and when i used the little bulb i saw it in action as the response was slow and delayed the bulb kinda didint shine at full from the start took a second or two. Yeah, the 10 ohm load at startup gave about 14 amps of load current and with about 140v DC after rectifier that puts the starting power at nearly 2KW, so my IRFP460 went dead. So, I used a 36v zener and as for turns ratio, (Primary 26 turns of 1.7mm ) and (Secondary. The only difference is that I adjusted the circuit for +36/-36 volts. I built it using the exact same parts written in the schematic. ![]() ![]() Hello everyone, I made a 50Khz SMPS using the schematic I have attached to my message. #SG3525 IR2110 SMPS RAREST SERIES#I took the bulb out, it's a 230 volt 500w bulb by the way and ' ups' it measures 10 ohms, so yeah no wonder why the mosfets went absolutely 'bananas':D so I guess I should put some kind of a dimmer thyristor or something in series when attaching such a load, or maybe you know of some higher current rated devices which I could swap into the IRFP460 using now? I mean something that could work well in this design just with higher current ratings? I guess i have to keep the gate capacitances moderate I just don't know which devices are fine by the IR2110 and which could bee to 'heavy' for the IR2110 to drive? Also even though in the feedback loop the zener i had was rated 82 volts, i still got only +-70 or 140 v DC out from the secondary, why is that shouldn't the octocoupler work with the SG3525 error amplifier as to sense the voltage and keep approximately 4v above the feedback zener voltage by either increasing the frequency or duty cycle which one i dont know? Ok my bad, I was wrong, yesterday i measured across the wire leads coming out of the lamp, turns out the very bulb itself had a bit corroded contacts, no problem for 220 volts but when measuring with multimeter they showed wrong resistance. #SG3525 IR2110 SMPS RAREST SOFTWARE#The other option could be innapropiate transformer core or something along those lines? Rip Software For Epson 1400 Free. Now a few question, could the problem be the feedback loop via the octocoupler,maybe it senses too low of a voltage and increases the frequency or duty cycle of the SG3525 too much and the transformer due to back emf creates some spikes in the process which killed my mosfets and the ic's driving them down the line? Free Download Hd Hollywood Movies In Dual Audio For Pc. Now i have had the same problem with other simple design smps, i guess when their simple their just not reliable enough under bigger loads.sadly they arent as robust and reliable as the age old transformers for mains. #SG3525 IR2110 SMPS RAREST CRACKED#It works that far it's okay but it worked when i had a 70w load light bulb attached to the output, after i tried going with a 500w bulb things just went bananas aka exploded, everything in the chain was dead and cracked open, both IRFP460 the IR2110 and also the SG3525 was dead as I later found out when replaced all other parts and still got not oscillation driving the IR2110. Hi folks, so I built an smps from a schematic found on the internet. ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |